Home » AMAZON » Husky Tool Box » Step Via Step Make The Easy DIY Picnic Table Bench Plans through gear set overview

Step Via Step Make The Easy DIY Picnic Table Bench Plans through gear set overview

The easiest season for outdoor relaxing is determined by where you are living. Inside the “sunshine state” (my neck of the woods), our seasons cross as follows: 3 weeks of iciness > 2 weeks of bliss > 1st love computer virus season > raging inferno / rainy season > second love computer virus season / typhoon season > 13 really nice days > then delicate to cold another time. In Florida, picnic season isn’t a time of 12 months, it’s a time of day. It’s that 5-minute window between getting soaking wet with rain and soaked with sweat. Alternatively wet or now not, you are able to’t stand up regularly; most often it’s essential to sit down down. This DIY picnic table endeavor is a superb family amassing position for slightly outdoor relaxing and collaborative love computer virus shooing, just about any season of the 12 months!

Assemble Your Private Picnic Table – An Easy Weekend Endeavor

Full sized 6-foot picnic table.
Complete sized 6-foot picnic table.

There are two vital numbers to remember while setting up your picnic table: 60 and 1,000. And to be trustworthy, I’m attempting laborious to fail to remember the second one. 60 is the number of ranges for the angled cuts and 1,000 is the number of ranges it used to be external all through maximum of this assemble.

Between plenty of daily rains, a typhoon scare and the unbearable tropical heat, I stretched this endeavor out over about two and a part weeks (after the local weather allowed me to even start). Alternatively given a super forecast (and in all probability help from a friend), it’s in point of fact a somewhat rapid 1-2 day endeavor.

Getting Started On Your DIY Picnic Table Endeavor

Pressure treated lumber
Proper right here’s the lumber I started with.

Enough small speak about. Let’s get this issue built so we’re in a position to have the benefit of it when the good local weather does come along, for those 2 transient weeks. Start through amassing provides. All of the wood is pressure treated and all {{hardware}} is rated for outdoor use and make contact with with treated wood.

Galvanized carriage bolts
Money saving tip: At the place of dwelling center, I was able to save lots of a pleasing little little bit of cashola through looking for those packs of 10 galvanized carriage bolts w/nuts from the chain link fence a part of the home center’s yard dept. They’ve been less expensive than the bolts by myself inside the {{hardware}} dept.

Provides List

Rigidity treated lumber (8′ long):

* (4 pieces) 2×8
* (4 pieces) 2×4
* (6 pieces) 2×6

{{Hardware}}:

* (16 pieces) 3/8” x 3” carriage bolts
* (16 pieces) 3/8” flat washers
* (16 pieces) 3/8” lock washers
* (16 pieces) 3/8” nuts
* (34 pieces) 4” x 10 deck screws
* (16 pieces) 2-1/2” x nine deck screws
* (4 pieces) 3” x nine deck screws

The deck screws are all self drilling, to avoid the need for pilot holes. The carriage bolts, washers and nuts are all galvanized.

Laying It All Out On The Table – The DIY Picnic Table

DIY Picnic table
Start through lowering each and every of the 2×8’s to a measurement of 72”.

I based this endeavor on standard picnic table designs. It’s rather a lot robust and might ultimate for a couple of years. With every little bit of lumber, first trim away one of the production facility ends, earlier any splits. Then take your dimension from that end. That way, each and every bit has two transparent, freshly scale back ends.

We’ll start with the table prime, then the legs and bench is helping. Next we’ll brace the legs so the picnic table doesn’t get all vulnerable at the knees. And ultimately we’ll upload the bench seating.

The Table Slats – DIY Picnic Table

1/4" spacers
I made six of the ones 1/4” spacer doo-dads to help align my table and bench slats.

The picnic table assemble starts with the perfect. Cross ahead and scale back all Four 2×8’s proper all the way down to 72” (6 toes). Imagine every bit and mark their best face with painter’s tape. Those will be the prime side (provide side) of the table.

Table slats with spacers
To house an umbrella, first align two of the table slats side through side. House them 1/4” apart.

My partner and I want the selection to make use of a giant patio umbrella with this table. I googled and situated that patio table umbrellas most often have a 1-1/2” diameter pole, so I decided I would really like an opening approx 1-3/4”. While you don’t want the umbrella hole, skip to the next section.

Laid out for umbrella pole cutout.
Put every excellent faces each up or down then draw a 1-3/4” circle at the halfway stage. I traced around a glue bottle that happens to be 1-11/16” in diameter (1/16” smaller, alternatively however massive enough to slide the pole in and out and not using a downside).
Relief cuts
This may well be difficult to cut with an opening spotted. Instead, use a jigsaw and make a chain of heterosexual support cuts.
Cutting the umbrella hole.
Then conform to the curve to remove the waste.
1-3/4" hole for umbrella.
My curve tracing wasn’t superb, but it surely’s close enough.

Table Is helping – A Tip Prime Tabletop Help Team of workers

Table supports
The two outer is helping have 60° miters. The middle help is beveled at 60°.

There are 3 table is helping (two outer and one middle), all of which might be scale back from 2×4’s. Every ends of each and every are scale back at 60° and attitude in path of each other.

Lay out a 60° miter.
For the main of 2 outer is helping, start through lowering a 60° miter at one end of a 2×4.

I used a T-bevel (aka “sliding bevel”, “false sq.” or “bevel gauge”) set to 60° to position out the miter cuts. However, you in all probability can use a 30-60-90 triangle or miter spotted.

Laying out table support.
Measure 28” from the aim and lay out for yet one more 60° scale back. The two bevels needs to be in opposite directions, angling in path of each other.
Cutting outer table support.
You are able to’t see in this image, alternatively the board is clamped to two paintings tables. Ensure that yours is secured previous than lowering.
Outer table supports.
Listed below are the outer table is helping. The long side measures 28”.

No One Wants A Dishevelled Heart – Now not Even Your DIY Picnic Table

Cutting a 30° bevel.
The principle bevel will trim away the perspective left at the back of from lowering the outer is helping.

I was able to get all 3 table is helping out of a unmarried 2×4. After you narrow the two outer is helping, set them aside and scale back the middle help. This piece moreover has 60° angles at each and every end. Alternatively this time we’re lowering bevels*, now not miters. Mark a sq. scale back line slightly earlier the perspective at the final a part of the 2×4.

* TIP: To cut a 60° bevel, tilt the one plate of your around spotted to 30°.

First cut on middle table support.
Proper here’s the main 60° bevel. Now turn the piece around and bevel the other end.

Very similar to with the two outer is helping, the cuts must attitude in in path of each other and the long edge must measure 28”.

In order for you the umbrella hole on your picnic table, scale back it with a 1-3/4” hole spotted, Forstner or spade bit. This is best carried out with a drill press. While you don’t want it, very good… no colour for you!

Drilling 1-3/4" hole.
Make a 1-3/4” hole inside the center of the middle table help. With an opening spotted, drill halfway from one side, turn the piece over and entire the scale back. Have in mind to clamp your workpiece to the drill press table.

Assembling The Table Prime – DIY Picnic Table Endeavor

DIY picnic table project.
Lay your table slats face down. Put 1/4” spacers between them and flippantly clamp the whole thing jointly so that not anything slides around. Degree the forums to each other the easiest you are able to.

Lay the forums with the easiest faces down (and best edges at the outsides). While you made an umbrella hole, be sure that those cutouts are situated inside the middle. Now you are able to attach the 3 is helping. The long measurement of each and every help is going against the table slats.

Attach The Outer Table Is helping

Attaching outer table supports.
Center the outer is helping and position them 7” from the highest of the table slats. Ensure that they’re sq. to the table slats.

Use 4” long #10 deck screws to glue the outer table is helping 7″ from the ends of the tabletop. Power two screws consistent with board. You’ll should first drill countersinks for the screw heads. Moreover, even though I used self drilling screws, in this step I decided to drill a counterbore (merely massive enough for the screw shaft to fit into) all over the outer is helping. I didn’t want to risk splitting the help pieces. I then let the screws drill their own way into the table slats.

Optimal screw depth.
Countersink the screws deep enough that they thread about this a long way (see exposed stage of the screw) into the table slats. Once you decide the optimal intensity, mark it on your drill bit with covering tape – or use a stop collar – in order that you won’t drill too deeply.

Fairly than counter-boring for the screw shafts (because of it does take a chronic drill bit that you simply would possibly not have readily to be had), it is conceivable you can instead want to power the screw slightly strategies, once more it out to transparent the shavings, power it slightly deeper, and so on until you’re all over the outer is helping. THEN attach them to the table prime slats.

Attach The Heart Table Help

Attaching the middle table support.
Attaching the middle table help.

Finally, position the middle table help. Take a look at that it’s sq. to the table and the hole (if you happen to occur to opted for one) is targeted over the only inside the table slats. Clamp the help in position then fasten it to the table prime with 8 2-1/2” long #nine deck screws, two consistent with slat. Do not countersink, alternatively do power the screw heads flush (or slightly underneath the ground).

It’s Bought Legs – It Is conscious about How To Use Them

Leg layout.
Earlier any cracks or splitting, mark and scale back a 60° miter at one end of a 2×6.

The Four legs are scale back from 2×6’s. Now not just like the table is helping, the ends of the legs are scale back parallel to each other (leaning within the similar route). Start through lowering a 60° attitude on one end of a 2×6. Then scale back the other end, mitered within the similar route, 40” from the main.

Leg layout.

Measure 40” from the aim of that scale back and lay out one different 60° miter parallel to the main (they want to every lean inside the similar route).
Next, we’ll scale back the aim off of one end of each and every leg.

Measuring for toe clipping.
On one end of each and every leg, measure 1-1/2” in from the aim of the miter, as confirmed.
Marking cut line.
Using a sq., mark a line perpendicular to the mitered end.
Trim that toenail.
Reduce on that line to remove the aim.
Picnic table foot.
That’s the foot end of the leg that can rest at the backside. It must now seem to be this.
1 of 4 legs.
In case you’re carried out, all Four legs must seem to be this.

Spread Eagle – Those Legs Cross All The Approach Up And Make A Table Of Themselves

Where the legs meet.
The legs bolt to the outer table is helping with the criteria jointly like this.

The next step is to glue the legs to the outer table is helping. Inside the previous step, we scale back the aim off of the foot end. The end is going up inside the air all through this step.

Leg hardware.
Each and every leg attaches with two 3/8” x 3” galvanized carriage bolts with flat washers, lower up washers and nuts.
First leg in place.
Clamp the main leg in position. Ensure that the miter sits flat at the table with the aim at the center of the opening between the middle table slats.

{{Hardware}} The Legs Cross – Glamorous Gams For Your Picnic Table

Prepping for the leg bolts.
First, countersink with a spade or Forstner bit. Then drill a 13/32” hole for the shaft of the bolt.

Arrange the {{hardware}} with the heads of the carriage bolts going during the floor of the table and the washers and nuts countersunk at the inside. The bolts are 3” long in order that they’ll conceal completely all through the wood, in no way giving unsuspecting knees the old-fashioned “howdy-do”.

Countersunk and counterbored.
Counter-bore all over the table help and the leg with a 13/32” drill bit.

Drill to countersink the nuts and washers. The holes needs to be massive enough in diameter for the flat washing machine and easily deep enough to deal with the two washers and nut, no deeper. I used a 1-1/8” Forstner bit alternatively your measurement may range (depending at the floor diameter of your washers).

Cinching up the leg bolts.
Push the carriage bolt in from the skin (the leg side) and tap with a hammer to seat the head. Then, into the countersink hole, position the flat washing machine followed through the lower up washing machine. Finally, thread at the nut and tighten.

Counter-sink first, then counter-bore for the bolt shafts. Have in mind to dodge the screws already operating by the use of the table is helping. It’s OK to stagger the holes if it’s essential to.

Picnic table leg bolts.
Repeat until all Four legs are mounted in position.

Bench Is helping – The Picnic Table Legs Help You So Yours Don’t Have To

Bench supports in place.
The bench is helping bolt to the legs and prevent them from spreading.

Next up: the bench is helping. Two, to be precise. Each and every bench help is scale back from a 2×4. The ends are 60° miters angled in the opposite direction (in in path of each other) and the long edge measures 60”.

Measuring for bench support position.
To determine where the bench is helping cross, mark the inside face of the legs 14” from the table prime. While you use a framing sq. like this, be sure to’re finding out the ruler at the floor!
Marking parallel to tabletop.
Deal with a smaller sq. up in opposition for your framing sq. and draw a line all through the legs at the 14” mark.

Mark the legs 14” from the table prime and connect momentary help blocks.

Temporary supports.
Use plenty of the scraps as momentary help blocks. Line them up beneath the lines you merely drew and clamp them in position.
Bench support in position.
Now rest a bench help at the momentary blocks. Orient it as confirmed (with the long edge down, in path of the table prime) and use a framing sq. to align the halfway stage with the middle of the table.

With the bench is helping fastened to the legs, each and every leg must have a whole of four carriage bolts: two at the table help and two at the bench help. After the whole thing’s bolted jointly, un-clamp and discard the momentary help blocks.

Fasten bench supports in place.
Clamp the bench help in position. Then countersink and counterbore for two carriage bolts (with washers and nuts) at each and every leg and connect the legs to the bench is helping, just like we did lower down at the table is helping.

Braces – Give Your DIY Picnic Table Something To Smile About

Picnic table leg brace.
The leg braces are scale back from 2×4’s. Start with a 60° miter on one end. Then measure 30-1/2” from the aim and make one different 60° scale back parallel to the main.

We’re now not proper right here to throw colour on your endeavor; that’s what the umbrella is for (did you opt for the hole?). Everyone knows your endeavor is your kid and we in point of fact really feel the similar way. Alternatively anyone has to mention it: your kid desperately needs braces. That’s now not our way of callously mocking a wayward overbite. Instead, we’re relating to the specified leg braces.

Leg brace blank.
The leg braces start like this (cross ahead and scale back two of the ones). Every edges are 30-1/2” long.

The leg braces are arguably one of the crucial the most important part of the picnic table endeavor. They aren’t difficult to make, alternatively do not be tempted to put out of your mind them. It is a heavy unit and – without the braces – it is not safe to use. We is in all probability all smiles now, but if your picnic table pancakes at the next shindig no person’s going to be flashing those pearly whites.

Custom designed Fit The Leg Braces – DIY Picnic Table Endeavor

Customizing the leg braces.
Deal with a leg brace like this, with the miter flat against the bench help and the other end placing down beside the table prime. Align the bottom of the miter flush with the lower edge of the bench help.

Since there will unquestionably be minor diversifications inside the distances between the middle table help and the outer is helping, the leg braces are scale back to fit.

Marking where to cut.
Mark where the “prime” edge of the bench help falls at the leg brace.
Mark at table line.
Without transferring the brace, draw a line where the table prime intersects the leg brace.

To avoid confusion or error, fit the main leg brace previous than starting to customize the other.

Perpendicular to mitered edge.
Use a sq. to draw a line where you marked at the “prime” of the bench help.
Marking other end for cut.
Moreover, verify that the street you drew along the bottom face of the table prime is perpendicular to the miter. If now not, lower up the honour and sq. it up now.

After marking and squaring the marks at every ends (as described above) scale back the criteria off, preserving your blade to the waste side of the lines.

Immediately From The Bird’s Mouth – Changing into The Leg Braces To The Heart Table Help

Brace in position for marking birdsmouth.
Rest the leg brace on prime of the middle table help, within the similar orientation as previous than. Ensure that the miter up prime is sitting flat against the bench help.

The next step is to cut a birdsmouth notch that can fit around the middle table help. For best results, verify that the legs are sq. to the table prime (or at least in truth close) previous than proceeding.

Marking for birdsmouth.
Use a sq. to draw a line at the edge of the middle table help.
Mark other half of birdsmouth.
Then rest the help flat at the table slats and draw a line level with the face of the middle table help.
Laid out and ready to cut the birdsmouth notch.
Birdsmouth layout.
Notch cut with jigsaw.
Reduce the notch with a jigsaw.
Overview of finished leg brace.
Evaluate of finished leg brace.

Finishing Up With The Leg Braces – DIY Picnic Table Bench Plans

Brace in place.
Fit the leg brace in position.

After shaping the leg brace, set it in position and connect with screws.

Fasten brace to bench support.
Fasten the brace to the bench help with two self drilling deck screws (use a three” long #nine screw with regards to the “prime” and a 4” long #10 screw underneath that).
DIY picnic table.
At the middle table help, I drilled a countersink hole to allow the screw to thread a super inch or so into the middle help piece. It’s angled slightly in path of the help.
Attaching brace.
Conscientiously power a self drilling 3” #nine deck screw. Goal for the middle help, alternatively try to leave out the hole. You don’t want to lower up the highest of the brace, so ponder counter-boring or backing the screw out a few events to transparent the dust as it drills its way by the use of the wood.

And now, repeat the process for the other leg brace.

The power of the brace.
This demonstrates the price of good bracing. Don’t do this until the braces are in position another way you’ll possibly cause hurt.
Relocating
While you’re operating by myself, like me, now is an effective time to move the table to its ultimate resting position.
Rolling the table upright.
Once in position, rigorously roll it over.

We Have A Picnic Table – Now For Somewhere To Sit down

We’re nearly carried out setting up the picnic table. The next step is to cut the bench slats. It is best to however have Four untouched 2×6’s. Reduce each and every to 68” (4” shorter than the table prime).

Since this is a endeavor designed for sitting – and folks most often shift and slide around as they sit down (most often wearing shorts) – I did a couple problems I wouldn’t most often do to an outside endeavor: I routed a 1/4” roundover on all Four bench slats and sanded their prime flooring (make a selection the easiest face because the perfect) and outer edges. I moreover routed all outer edges of the table prime.

1/4" roundover
I routed a 1/4” roundover on all corners of all Four bench slats. It takes only a minute or two consistent with slat and the payoff is huge. Even though there may be production facility round-overs, rout over them anyway.

I extraordinarily suggest taking the time to rout and sand the bench slats. It doesn’t take almost as long as it’s possible you’ll suppose and it makes for a clean, comfortable in point of fact really feel. Best of all, outdoor family time won’t be ruined through nasty splinters on your members of the family’ legs and hindquarters.

Sanding bench slats.
I sanded the perfect faces and all edges of the bench slats with a Ridgid 18V Octane ¼ sheet sander that we’re checking out for an upcoming review. The integrated 80-grit paper made rapid paintings of this procedure.

Then, moreover for comfort, I routed the similar roundover on all external edges of the table prime. I didn’t sand the table prime, alternatively you are able to if you’d like or should.

Routing the table top edges for comfort.
While you have the trim router out, cross ahead and run it around all external edges of the table prime.
Rounding over the hard corners.
Don’t forgot the bottom and corner edges.

Intermediate Bench Is helping – Stiffen The Benches On Your DIY Picnic Table Endeavor

Intermediate bench supports.
The long face of the intermediate bench is helping measure 10”.

The overall components to cut are two fast help pieces that cross in the middle of the bench seats. Like the middle table is helping, those keep the slats aligned and help stop sagging beneath load.

Attaching the intermediate support.
Lay out a couple of bench slats and connect an intermediate bench help.

To gather the intermediate is helping to the bench slats, lay a couple of slats with the sanded side (the perfect, butt touch side) going thru down. Align the slats side-by-side with 1/4” spacers and gently clamp the ends to hold the whole thing however when you fasten the help.

Screwed in place.
Sq. the help piece to the bench slats and power two 2-1/2” #nine deck screws consistent with slat. The longer (10”) face needs to be down, against the slats. Because of this is a fast piece, I staggered the screws to reduce the chance of splitting.

You Would possibly Now Technique The Bench – A Position To Rest Your Weary Bones

Centering the bench slats.
Center the bench slat assemblies side to side. I’m using a mixture sq. to hunt out the aim where the overhang is identical on each and every end.

Position the main set of bench slats and clamp them in position. Then tip the picnic table on edge and screw them to the bench is helping. Take care that the table doesn’t tip while attaching the benches.

1/2" overhang.
Allow the doorway edge of the bench slats to overhang the is helping through part”.
Bench slats clamped to picnic table.
Clamp to every bench is helping.
Picnic table stood on edge.
Conscientiously stand the picnic table on edge.
Screwing the bench slats in place.
Attach the bench with two 4” long #10 deck screws (two consistent with slat). You’ll should counter-sink enough that the screws thread lots of the way into the bench slats.

After you get the main bench fastened, rigorously right kind the table then stand it at the reverse edge and connect the other bench.

DIY picnic table project.
The screws with regards to the ends attitude outward like this.

Bench Press – Benefit from Your DIY Picnic Table!

Enjoying the fruits of my labor!
As I press my cheeks against the bench, I wonder the delicate complexities of existence while feeling thankful that I finally got enough rain-free hours to finish this endeavor.

You’re carried out, and likewise you’re now a certified at recommendations on how one can assemble a picnic table bench set! There were a ton of pictures for the sake of clarity, and that can make it appear to be a chronic, difficult assemble. Alternatively if you happen to occur to conform to along and assemble your own picnic table, you’ll possibly agree this used to be a easy, relaxing endeavor. From proper right here you are able to go away it as is or finish it any way you’d like.

Paint, deck stain or spar urethane would upload a layer of protection and wonder while squeezing a few additional years of existence from your picnic table endeavor. When the liquid sunshine eases up slightly additional, I’ll be using a deck stain/sealer on mine.

Now grasp yourself a cold one, sit down down and calm down. You’ve earned it! Alternatively hurry up, additional rain is on the easiest way.

Other Collections of Step Via Step Make The Easy DIY Picnic Table Bench Plans through gear set overview

Life is a picnic eat it up with these

Add a Comment

Your email address will not be published. Required fields are marked *